AB变频器功能端子表
基本显示参数Basic Display | 功能 | 基本编程Basic Progran Group | 功能 | |||
b001 | 输出频率 | P031 | motor NP Volts(电动机铭牌电压) | |||
b002 | 命令频率 | P032 | motor NP Hertz (电动机铭牌频率) | |||
b003 | 输出电流 | P033 | motor OL current(电动机额定电流 ) | |||
b004 | 输出电压 | P034 | minimum Freq(最小频率 )0.00Hz | |||
b005 | 直流母线电压 | P035 | maximum Freq(最大频率)50HZ | |||
b006 | 变频器状态 | P036 | Start Source(起动源)2-wire 002 | |||
b007 | 故障代码1 | P037 | Stop mode(停止模式)coast 005 | |||
b008 | 过程显示 | P038 | Speed Reference(速度基准值)Analog in1 002 | |||
b0010 | 输出功率 | P039 | Accel Timel(加速时间为15秒)Sec | |||
b0011 | 已用电MVVｈ | P040 | Decel Timel(减速时间为10秒)Sec | |||
b0012 | 运行时间 | P041 | Reset to Defalts复位为默认值工Ready/Zdle 000 | |||
b0013 | 转矩电流 | P042 | Auto mode(自动模式) NO Function 003 | |||
b0014 | 变频器温度 | P043 | Motor OL Ret(电机过载值存储)Disabled 000 | |||
b0015 | 已用电KWｈ | |||||
注：b参数是变频器自动默认不用修改 | ||||||
端子 Terminal Block Group | 功能 | 端子 Terminal Block Group | 功能 | |||
T051 | Terminal Block(数字量输入1选择) Digital in1 sel | T052 | Digital In2 sel(数字量输入2选择)Local 003 | |||
T053 | Digital In3 sel(数字量输入3选择) Clear Fault 010 | T054 | Digital In4 sel(数字量输入4选择) Comm port 004 | |||
T055 | Relay out1 sel (继电器输出1选择)Ready/Fault 000 | T056 | Relay out1 Level (继电器输出1幅值)0.00 | |||
T058 | Relay 1 on Time(继电器1接通On时间)0.00 sec | T059 | Relay 1 off Time(继电器1断开Off时间)0.00 sec | |||
T060 | 1. Relay out 2 sel(数字量输出2选择) motor Running 002 | T061 | Relay out 2 Level (继电器输出2幅值)0.00 | |||
T063 | Relay 2 on Time(继电器2接通On时间)0.00 sec | T064 | Relay 2 off Time(继电器2断开Off时间)0.00 sec | |||
T065 | Opto out sel (光电耦合输出选择)At Frequency 001 | T066 | Opto out Level(光电耦合输出幅值)0.00 | |||
T068 | Opto out Logic (光电耦合输出逻辑) 0.00 | T069 | Analog In 1 Sel(模拟量输入1选择) 4-20mA 001 | |||
T070 | Analog In 1 LO(模拟量输入1下限) 0.0% | T071 | Analog In 1 Hi(模拟量输入1上限)100.0% | |||
T072 | Analog In 1 Loss(模拟量输入1丢失)Disabled 000 | T073 | Analog In 2 Sel(模拟 量输入2选择) 0-10V 002 | |||
T074 | Analog In 2 LO(模拟 量输入2限) 0.0% | T075 | Analog In 2 Hi(模拟量输入2上限)100.0% | |||
T076 | Analog In 2 Loss(模拟量输入2丢失)Disabled 000 | T077 | Sleep-wake sel (休眠-唤醒选择) Disabled 000 | |||
T078 | Sleep-Level (休眠等级) 10% | T079 | Sleep-Time(唤醒时间) 0.0 SEC | |||
T080 | wake-Level(唤醒等 级) 15% | T081 | wake-Time(唤醒时间) 0.0 SEC | |||
T082 | Analog out 1 sel (模拟量输出1选择) outFreq 0-10V 000 | T083 | Analog out 1 High (模拟量输出1上限)100% | |||
T084 | Analog out 1 setpt(模拟量输出1设定点)0.0% | T085 | Analog out 2 sel (模拟量输出2选择) outcurr 0-10V 001 | |||
T086 | Analog out 2High (模 拟量输出2上限)100% | T087 | Analog out 2 setpt(模拟量输出2设定点)0.0% | |||
T088 | Anlg Loss Delay (模拟量丢失延时)0.0 SEC | T089 | Analog In Filter (模 拟量输入上限)0 | |||
通信语言Communications Group | 功能 | 通信语言Communications Group | 功能 | |||
C101 | Language(通信语言)001 English | C102 | Comm Format(通信格式) | |||
C103 | Comm Data Rate(通信数据速率)003 9600 | C104 | Comm Node Addr(通信节点地址) | |||
C105 | Comm Loos Action(通信丢失动作) | C106 | Comm Loos Time(通信丢失时间) | |||
C107 | Comm Write Mode(通信写模式) | C108 | Start Source2(通信起动命令源2) | |||
高级编程Advanced Program Group | 功能 | 高级编程Advanced Program Group | 功能 | |||
A141 | Advanced Program Group(消防强制输入频率)Purge Frequency | A142 | Internal Freq(内部频率)60Hz | |||
A143 | Preset Freq0(预置频率0)0.0Hz | A144 | Preset Freq1(预置频率1)5.0Hz | |||
A145 | Preset Freq2(预置频率2)10.0Hz | A146 | Preset Freq3(预置频率1)20.0Hz | |||
A147 | Accel Time 2(加速时间2)30.00 Sec | A148 | Decel Time 2(减速时间2)30.00 Sec | |||
A149 | S Curve%(S曲线%)20% | A150 | PID Trim Hi(PID整定上限)60HZ | |||
A151 | PID Trim LO(PID整定下限)0.0HZ | A152 | PID Ref sel(PID基准值选择)PID setpoint 001 | |||
A153 | PID Feedback sel (PID反馈值选择)Anaiog In1 000 | A154 | PID Prop Gain(PID比例增益) 1 | |||
A155 | PID Integ Time(PID积分时间)10.0 Ssc | A156 | PID Diff Rate(PID微分速率)0.00 1/Sec | |||
A157 | PID Setpoint(PID设置点)50% | A158 | PID Deadband(PID死区)0.0% | |||
A159 | PID Preload(PID预负载)0.0HZ | A160 | PID Process Factor (PID过程因数)30.0 | |||
A163 | Auto Rstrt Tries(自动重新起动尝试)0 | A164 | Auto Rstrt Delay(自动重新起动延时)1.0 Sec | |||
A165 | Start At PowerUp (上电起动)Disabled 000 | A166 | Reverse Disable (反向 禁止)REV Disabled 001 | |||
A167 | Flying Start En (飞速起动使能)Disabled 000 | A168 | Pwm Frequency(PWM频率) 4.0KHz | |||
A169 | Pwm Mode(PWM模式) 2-Phase 001 | A170 | Boost select(升压选择)45.0VT 004 | |||
A171 | Start Boost(起动升压) 2.5% | A172 | Break Voltage(转折电压)25% | |||
A173 | Break Frequency (转折频率)15.0Hz | A174 | Maximum Voltage(最大电压)460 VAC | |||
A175 | slip Hertz @ FLA(满载滑差频率补偿)2.0Hz | A176 | DC Brake Time(直流制动时间)0.0 SEC | |||
A177 | DC Brake Level(直流制动幅值) | A178 | DC Brk Time@Strt(起动时直流制动时间)0.01SEC | |||
A179 | Current Limit 1(电流限幅1) | A180 | Current Limit 2(电流限幅2) | |||
A181 | Motor Select(电动机过载选择) | A182 | Drive OL Mode(变频器过载模式) | |||
A183 | SW Current Trip(软件电流跳闸) | A184 | Load Loss Level(负载丢失幅值) | |||
A185 | Load Loss Time (负载丢失时间) | A186 | Stall Fault Time (堵转故障时间) | |||
A187 | Bus Reg Mode (总线调节模式) | A188 | Skip Frequency1(跳变频率1) | |||
A189 | Skip Freq Band1(跳变频率宽带1) | A190 | Skip Frequency2(跳变频率2) | |||
A191 | Skip Freq Band2(跳变频率宽带2) | A192 | Skip Frequency3(跳变频率3) | |||
A193 | Skip Freq Band3(跳变频率宽带3) | A194 | Compensation(补偿) | |||
A195 | Reset Meters(测量复位) | A196 | Testpoint Sel(测试点选择) | |||
A197 | Fault Clear(故障清除) | A198 | Program Lock (编程锁定) | |||
A199 | Motor NP Poles(电动机铭牌极对数) | A200 | Motor NP FLA(电动机铭牌电流) | |||
| ||||||
辅助继电器Aux Relay Card Group | 功能 | 辅助继电器Aux Relay Card Group | 功能 | |||
R221 | Relay Out3 Sel (继电器输出3选择) | R222 | Relay Out3 Level (继电器输出3幅值) | |||
R224 | Relay Out4 Sel (继电器输出4选择) | R225 | Relay Out4 Level (继电器输出4幅值) | |||
R227 | Relay Out5 Sel (继电器输出5选择) | R228 | Relay Out5 Level (继电器输出5幅值) | |||
R230 | Relay Ou63 Sel (继电器输出6选择) | R231 | Relay Out6 Level (继电器输出6幅值) | |||
R233 | Relay Out7 Sel (继电器输出7选择) | R234 | Relay Out7 Level (继电器输出7幅值) | |||
R236 | Relay Out8 Sel (继电器输出8选择) | R237 | Relay Out8 Level (继电器输出8幅值) | |||
R239 | Aux Motor Mode (辅助电机模式) | R240 | Aux Motor Qty(辅助电机数量) | |||
R241 | Aux 1 Start Freq(辅助1起动频率) | R242 | Aux 1 Stop Freq(辅助1停止频率) | |||
R243 | Aux 1 Ref Add(辅助1频率增加) | R244 | Aux 2 Start Freq(辅助2起动频率) | |||
R245 | Aux 2 Stop Freq(辅助2停止频率) | R246 | Aux 2 Ref Add(辅助2频率增加) | |||
R247 | Aux 3 Start Freq(辅助3起动频率) | R248 | Aux 3 Stop Freq(辅助3停止频率) | |||
R249 | Aux 3 Ref Add(辅助3频率增加) | R250 | Aux Start Deiay(辅助起动延时) | |||
R251 | Aux Stop Deiay(辅助停止延时) | R252 | Aux Prog Delay(辅助控制延时) | |||
R253 | Aux AutoSwap Tme (辅助自动切换延时) | R254 | Aux AutoSwap Lvl (辅助自动切阀值) | |||
| ||||||
Advanced Display Group | 功能 | Advanced Display Group | 功能 | |||
d301 | Control Source(控制源) | d302 | Control Source(控制输入状态) | |||
d303 | Comm Display Group(通讯状态) | d304 | PID Setpnt Displ(PID设定点显示) | |||
d305 | Analog In 1(模拟量输入1) | d306 | Analog In 2(模拟量输入2) | |||
d307 | Fault 1 Code(故障代码1) | d308 | Fault 2 Code(故障代码2) | |||
d309 | Fault 3 Code(故障代码3) | d310 | Fault 1 Time-hr(故障时间1-小时) | |||
d311 | Fault 1 Time-min(故障时间1-分钟) | d312 | Fault 2 Time-hr(故障时间2-小时) | |||
d313 | Fault 2 Time-min(故障时间2-分钟) | d314 | Fault 3 Time-hr(故障时间3-小时) | |||
d315 | Fault 3 Time-min(故障时间3-分钟) | d316 | Elapsed Time-hr(消逝时间-小时) | |||
d317 | Elapsed Time-min(消逝时间-分钟) | d318 | Output Powr Fctr(输出功率因数) | |||
d319 | Testpoint Data(测试点数据) | d320 | Control SW Ver(控制版软件版本) | |||
d321 | Drive Type(变频器类型) | d322 | Output Speed(输出速度) | |||
d323 | Output RPM(输出速度) | d324 | Fault Frequency(输出速度) | |||
d325 | Fault Current(输出速度) | d326 | Fault Bus Volts(输出速度) | |||
d327 | Status @ Fault(输出速度) | |||||
本文来源：https://www.2haoxitong.net/k/doc/4708799549649b6648d747d6.html
文档为doc格式